- 您现在的位置：买卖IC网 > Sheet目录314 > AT93C56A-10TU-2.7 (Atmel)IC EEPROM 2KBIT 2MHZ 8TSSOP
AT93C56A/66A
4. Functional Description
The AT93C56A/66A is accessed via a simple and versatile three-wire serial communication
interface. Device operation is controlled by seven instructions issued by the host processor. A
valid instruction starts with a rising edge of CS and consists of a Start Bit (logic “1”) followed
by the appropriate Op Code and the desired memory address location.
READ (READ): The Read (READ) instruction contains the address code for the memory loca-
tion to be read. After the instruction and address are decoded, data from the selected memory
location is available at the serial output pin DO. Output data changes are synchronized with the
rising edges of serial clock SK. It should be noted that a dummy bit (logic “0”) precedes the 8- or
16-bit data output string. The AT93C56A/66A supports sequential read operations. The device
will automatically increment the internal address pointer and clock out the next memory location
as long as Chip Select (CS) is held high. In this case, the dummy bit (logic “0”) will not be
clocked out between memory locations, thus allowing for a continuous stream of data to be read.
ERASE/WRITE (EWEN): To assure data integrity, the part automatically goes into the
Erase/Write Disable (EWDS) state when power is first applied. An Erase/Write Enable (EWEN)
instruction must be executed first before any programming instructions can be carried out.
Please note that once in the EWEN state, programming remains enabled until an EWDS instruc-
tion is executed or V CC power is removed from the part.
ERASE (ERASE): The Erase instruction programs all bits in the specified memory location to
the logical “1” state. The self-timed erase cycle starts once the ERASE instruction and address
are decoded. The DO pin outputs the Ready/Busy status of the part if CS is brought high after
being kept low for a minimum of 250 ns (t CS ). A logic “1” at pin DO indicates that the selected
memory location has been erased, and the part is ready for another instruction.
WRITE (WRITE): The Write (WRITE) instruction contains the 8 or 16 bits of data to be written
into the specified memory location. The self-timed programming cycle t WP starts after the last bit
of data is received at serial data input pin DI. The DO pin outputs the Ready/Busy status of the
part if CS is brought high after being kept low for a minimum of 250 ns (t CS ). A logic “0” at DO
indicates that programming is still in progress. A logic “1” indicates that the memory location at
the specified address has been written with the data pattern contained in the instruction and the
part is ready for further instructions. A READY/BUSY status cannot be obtained if the CS is
brought high after the end of the self-timed programming cycle t WP .
ERASE ALL (ERAL): The Erase All (ERAL) instruction programs every bit in the memory array
to the logic “1 ” state and is primarily used for testing purposes. The DO pin outputs the
Ready/Busy status of the part if CS is brought high after being kept low for a minimum of 250 ns
(t CS ). The ERAL instruction is valid only at V CC = 5.0V ?? 10%.
WRITE ALL (WRAL) : The Write All (WRAL) instruction programs all memory locations with the
data patterns specified in the instruction. The DO pin outputs the Ready/Busy status of the part if
CS is brought high after being kept low for a minimum of 250 ns (t CS ). The WRAL instruction is
valid only at V CC = 5.0V ± ? 10%.
ERASE/WRITE DISABLE (EWDS): To protect against accidental data disturb, the Erase/Write
Disable (EWDS) instruction disables all programming modes and should be executed after all
programming operations. The operation of the READ instruction is independent of both the
EWEN and EWDS instructions and can be executed at any time.
7
3378O–SEEPR–11/09
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
AT93C86AY6-10YH-1.8
IC EEPROM 16KBIT 2MHZ 8MAP
ATAVRBFLY
KIT EVALUATION AVR BUTTERFLY
ATAVRXBNDL
XMEGA XPLAIN AND DISPLAY MODULE
ATDH2222
ADAPTER FOR ATDH2200 20PLCC
ATDH2225
CABLE ISP FOR AT17
ATDH2227
ADAPTER FOR ATDH2200 44PLCC
ATEVK1101
KIT DEV/EVAL FOR AVR32 AT32UC3B
ATF15XXDK3-SAX20
KIT DEV 20TSSOP ADAPTER ATF15XX
相关代理商/技术参数
AT93C56A-10TU-2.7-RET
制造商:Atmel Corporation 功能描述:
AT93C56A-10TU-2.7-T
功能描述:IC EEPROM 2KBIT 2MHZ 8TSSOP 制造商:microchip technology 系列:- 包装:带卷（TR） 零件状态:停產 存储器类型:非易失 存储器格式:EEPROM 技术:EEPROM 存储容量:2Kb （256 x 8，128 x 16） 时钟频率:2MHz 写周期时间 - 字，页:10ms 存储器接口:SPI 电压 - 电源:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C（TA） 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商器件封装:8-TSSOP 基本零件编号:AT93C56 标准包装:5,000
AT93C56AD3-10DH-1.8
制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Three-wire Serial EEPROM
AT93C56AU3-10UI-1.8
制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:3-wire Serial EEPROMs 2K (256 x 8 or 128 x 16)
AT93C56AU3-10UI-2.7
制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:3-wire Serial EEPROMs 2K (256 x 8 or 128 x 16)
AT93C56AU3-10UU-1.8
功能描述:电可擦除可编程只读存储器 Serial 电可擦除可编程只读存储器
RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
AT93C56A-W1.8-11
制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Three-wire Serial EEPROM
AT93C56AW-10SI-1.8
功能描述:IC EEPROM 2KBIT 2MHZ 8SOIC RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:96 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并联 电源电压:2.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP 包装:托盘